Woodsmith August/September 2021

Every project featured in Woodsmith contains detailed, step-by-step illustrations and clearly written instructions to guide you through each stage of construction — whether you’re a beginner or a seasoned woodworker. Plus, you’ll get practical, hands-on information covering woodworking techniques, tools, and tips.

United States
Active Interest Media
ESPECIAL: Save 50% on your subscription!
US$ 6,99
US$ 29US$ 14,50
6 Números

en este número

1 min.
from the editor sawdust

What is woodworking? For real, I’d like to know. I’ve been part of a few discussions recently about whether a given technique or project constitutes legitimate woodworking. For some folk, it centers around furniture projects built with solid wood joinery. For others, it’s all about hand tools. I’ll submit this issue as a practical example of how I’d answer the question. We have a couple furniture projects (cabinet and coffee table), a model boat, a reading lamp, and a shop-built vise for cutting joints by hand. In the departments, we have the usual articles on the router and table saw. Erich Lage, who in a past life was a trim carpenter, looks at installing a door. Vic Tesolin shows show to punch up a cabinet door with veneer. The point is woodworking…

1 min.
dillon baker, project designer

Dillon Baker is a contributing editor for Popular Woodworking and the design editor for Woodsmith magazine. His long-standing appreciation of the duality of art and functionality in furniture design, and his technical expertise in crafting both modern and traditional pieces, allow him to approach each project with unique perspectives and a high degree of creativity. Dillon holds a BFA in design from Iowa State University, and prior to entering the publication world, ran a design and build studio in downtown Des Moines, Iowa. Dillon both designed and wrote (his first) the Scissor Lamp project on page 32.…

1 min.
reader’s tips

Adjustable Router Stop Block There are occasions when I need to rout multiple mortises in a large workpiece. A recent project was a bed headboard. Instead of laying out the mortises and trying to eyeball where to stop routing, I decided to make a few stops that I could use with my router. You can see the stops in the photo at left. SIMPLE, BUT WORKS. The construction of the stop blocks is easy. The stops are an easy build from plywood. A fixed front fence is attached to a top plate. The movable fence is attached to the top plate with a screw through a slot. This way, the stop block works with a wide range of workpiece thicknesses. The inside of the stops are lined with adhesive-backed sandpaper for extra…

1 min.
quick tips

Sticky Tack Painter Points. Marc Hopkins of Des Moines, IA was looking for a way to hold some small chess pieces in place while flocking the bottom. Sticky tack to the rescue! It not only temporarily secures the pieces, but it’s the perfect solution to keep from marring up any of the finish he had already applied. Even Pressure. Chris Fitch of Winterset, IA has a quick tip to get even pressure when he has a large glueup. By layering a couple of pieces of painter’s tape in the center of a board being used as a caul, he is creating a “crown.” This allows for the pressure to start in the center of the caul ensuring even pressure when tightening down on your clamps. Tighten Loose Miter Bars. Carol Holly of…

8 min.
installing a pre-hung door

Hanging a door is one of the main tasks of a trim carpenter. Trim carpentry is woodworking on tour. Like a band on the road, working outside the controlled environment of the studio (or your shop) presents new challenges. The main challenge being that trim carpentry is woodworking that’s attached to, or integrated with, something larger. That larger thing in this case is a wall in your house. Trim carpentry is the art and craft of blending rough framing and precise woodworking. It can be a lot of fun when you know ahead of time the challenges that you’ll run into and how to tackle them. Let’s take a look at those challenges, starting with the anatomy of a pre-hung door. A PRE-HUNG DOOR The main drawing you see on the previous page…

7 min.
setting up a carving space

The longer I’m around woodworking and woodworkers, the more I realize just how broad this craft is. My projects tend toward furniture and cabinets. But in the last few years, I’ve dabbled in some carving. It offers a change of pace and a set of new skills to learn — and tools to get. Along the way, I’ve discovered that carving has different workshop needs than what I already have set up. The biggest difference is that you don’t need much space at all. While there’s a lot of information about setting up furniture making shops, there isn’t much on creating a space for a dedicated carver. So my aim is to talk about the big ideas of a carving shop: worksurfaces and work-holding, lighting, and layout, then we’ll get into the…